Afx VTL254HOMV Bedienungsanleitung PDF herunterladen

VTL Series Vapor Tight Strip Light

Models: 228-8MV, 228MV, 232-8MV, 232E8EM 120-277VAC 50/60Hz

232MVEM, 232MVHL, 232MVEM, 232MVHL

232E8, 232MV, 254HO-8MV, 254HOMV

8060301 R8

1 of 1

Limited Factory Warranty

AFX warrants this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period

of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it

does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with these

instructions could result in potentially fatal electric shock and/or

property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any fixture

with wet hands or while standing on a wet or damp surface or in water.

This fixture is designed for use in a 120-277VAC, 50/60Hz fused

circuit. Do not use on a dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) contact

between this fixture and the ground connection of your main power

supply panel.

This fixture is intended to be mounted 4ft above ground and used for

general indoor or outdoor lighting in wet locations.

Installation Instructions

1. Warning: Disconnect electrical power before

installing this fixture.

2. Release latches (Fig. 2-A) and remove diffuser.

Release gear assembly from housing clips (Fig. 2-B).

Gear tray is tethered to housing (Fig. 2-C).

3. Identify indentations in fiberglass housing for desired

power entry. Holes are supplied for end connections

and are capped with hole plugs. Top power entry

openings will need to be drilled. (Fig. 1-A)

4. Indentations are provided for mounting. Drill holes through housing at appropriate

locations. (Fig. 1-C) Warning – drilling holes in the housing is only permitted

for damp locations. For wet locations, use the mounting bracket kit (included).

5. Install latches into fiberglass housing latch mounting slots. (Fig. 1-B & 2-A)

6. To locate, hold fixture assembly up to ceiling with power supply knockout located

over entryway for power supply wires. Mark the locations of the mounting holes on

the ceiling.

7. Take the fixture down and punch a small hole into the ceiling at each location using

a nail or an awl to see if there is a wood joist. Attach to surface using fasteners and

sealing washers (by others) appropriate to ceiling materials.

8. If there is a joist, use a suitable wood screw (not included) to mount the channel.

(Fig. 4-A) Where there is no joist to screw into, use a toggle bolt (not provided)

(Fig. 4-B) of suitable length to mount housing securely to the ceiling.

9. Mount the fixture with appropriate mounting hardware (Fig. 4-A or B) while passing

the supply power wire (Fig. 3-B), the supply neutral wire (Fig. 3-A) and the supply

ground wire (Fig. 3-C) from junction box (Fig 3-D) or power supply through the

appropriate knockout hole into the fixture.

10. Use wire nut to connect white wire from ballast to neutral supply wire. (Fig. 3-A) Strip

supply wires if needed. (Fig. 3-E) Use wire nut to connect black wire from ballast to power

supply wire. (Fig. 3-B) Cover wire nuts and connections completely in electrical tape. Secure

bare or green ground wire to green screw in the channel. Note – for models with luminaire

disconnect pre-wired to ballast, reference the included instruction insert.

11. Re-install gear assembly to housing by snapping into clips (Fig. 2-B)

12. Install appropriate lamp(s) (not included) by inserting lamp pins into lamp holder. Rotate

into place to seat lamp for proper connection.

13. Mount Fiberglass diffuser onto Fiberglass housing, Secure by rotating latches around edge of

housing and capturing diffuser with rounded lip, snap latch closed. 6 or 12 latches total.

(Fig. 5-A). Restore power.

Fig. 1

Fig. 2

Fig. 5

Safety Precautions 1

Inhaltsverzeichnis

Seite 1 - Safety Precautions

VTL Series Vapor Tight Strip Light Models: 228-8MV, 228MV, 232-8MV, 232E8EM 120-277VAC 5

Verwandte Modelle: VTL228MV

Kommentare zu diesen Handbüchern

Keine Kommentare

Afx VTL254HOMV Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Afx VTL254HOMV herunter. AFX VTL254HOMV User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: VTL228MV

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Afx VTL254HOMV