Models:
1 of 2
Read all safety precautions and installation instructions carefully before
installing or servicing
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is re
commended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
ASSEMBLY
1.
Preparing for installation
A.
Disconnect electrical power
fixture.
B.
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
2. Wiring-
all wiring must take place inside junction box.
Caution:
Make sure power is off at fuse or circuit breaker box. Chec
power wires for damage or scrapes. If
three inches of the ballast
(194F).
Note:
Most dwellings built before 1985 have supply wire rated to 60C.
Consult a qualified elect
rician before installing.
A. Loosen four
clockwise.
B. Pre-Install gem bar
screws (2) (supplied).
C.
Mark two mounting holes locations on the ceiling by us
plate as a template. Remove the gem bar plate and drill two holes for the
anchors (13) supplied. Install the anchors.
D. Re-
install the gem bar plate (1) by securing it with two screws (2) on the
junction box and two screws (14) on the ceiling.
C. Make all wires
nuts (supplied).
D.
screw in the gem bar.
E.
The black wire from the fixture is connected to the black wire fr
power source.
F.
The white wire from the fixture is connected to the white (neutral) wire
from power source.
G.
Tuck all connections neatly into junction box.
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
wet or damp surface or in water.
Preparing for installation
Disconnect electrical power
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Chec
power wires for damage or scrapes. If
the
power supply wires are within
power supply
, use wire suitable for at least
Most dwellings built before 1985 have supply wire rated to 60C.
rician before installing.
emove gem bar (1) by
(1) on the junction box by securing it with two
Mark two mounting holes locations on the ceiling by us
plate as a template. Remove the gem bar plate and drill two holes for the
anchors (13) supplied. Install the anchors.
install the gem bar plate (1) by securing it with two screws (2) on the
junction box and two screws (14) on the ceiling.
to the
s
from the fixture and power source to the green
The black wire from the fixture is connected to the black wire fr
The white wire from the fixture is connected to the white (neutral) wire
Tuck all connections neatly into junction box.
120VAC / 60Hz
This fixture is designed for use in a 110
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
locations.
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Chec
k
power supply wires are within
, use wire suitable for at least
90C
Most dwellings built before 1985 have supply wire rated to 60C.
(1) on the junction box by securing it with two
Mark two mounting holes locations on the ceiling by us
ing gem bar
plate as a template. Remove the gem bar plate and drill two holes for the
install the gem bar plate (1) by securing it with two screws (2) on the
with wire
from the fixture and power source to the green
The black wire from the fixture is connected to the black wire fr
om
The white wire from the fixture is connected to the white (neutral) wire
8060745 R0
120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
indoor lighting in damp
at fuse or circuit breaker box before installing or servicing any part of this
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
Kommentare zu diesen Handbüchern